CNC MACHINING

Low-Volume CNC Machining in China, from 1 Piece

Low-volume CNC machining in China from 1 piece: milling, turning and 5-axis routes selected around the geometry, material and assembly requirements of each OEM component.

Machined aluminum housing with stepped bores, bosses and an offset port

Five-axis access for complex geometry

Multi-face housings, angled interfaces and curved surfaces may benefit from five-axis machining. Many of these parts only need indexed 3+2 positioning; simultaneous five-axis is for continuous contours.

Five-axis machining applications and engineering review

What drives the price and the route

  • Quantity: a fixture or a dedicated program pays off at some quantities and not at others, so the quantity can change the route as well as the unit price.
  • Fit-critical interfaces: bores, sealing faces and locating features that need a finishing pass, reaming or grinding, and the inspection that goes with them.
  • Geometry: thin walls, deep pockets and long cutter reach slow the cut, and each extra setup adds time and a chance of position error.
  • Finish: anodizing or plating needs a size allowance or masking on fits, which has to be decided before machining.
Processes, equipment and manufacturing review

Prototype, low-volume and repeat orders

Development parts are made to the current drawing, with the measurements you need for the assembly trial. Repeat orders are made to the approved revision, material, finishing and inspection plan. Typical production lead time is 7 to 30 days, depending on how complex the parts are and how many you need. It is counted from order confirmation and receipt of the payment due before production, as stated on the quotation, to the day the inspected parts are packed and ready to ship. Shipping transit time is not included and is confirmed separately on the quotation. If the material is not in stock and has to be bought in, allow up to about one more week.

Compare production stages

CNC machining capability ranges

The ranges below describe typical limits for custom CNC machined parts. Every drawing is reviewed individually, and the achievable tolerance depends on material, size, wall thickness and the feature being controlled.

Minimum order
1 piece, from single prototypes to repeat batches
Milled part size
Up to 2500 × 2000 × 900 mm
Turned diameters
Ø4 to Ø500 mm, length up to 700 mm
General tolerance
ISO 2768-m unless the drawing states otherwise
Critical features
±0.005 mm on turned, ground and wire-EDM features; ±0.01 mm on milled bore positions
Surface roughness
Ra 1.6 µm machined, Ra 0.4 µm ground
Processes
3-axis and 5-axis milling, CNC turning, turn-mill, wire EDM, grinding
Inspection
CMM, 2D vision measurement, roughness testing, thread and pin gauges

Materials we machine

Aluminum alloys

6061-T6, 6082-T6 and 7075-T6 for housings, brackets, plates and lightweight robot structures. Anodizing, hard anodizing and bead blasting are common finishes.

Stainless and alloy steels

303, 304, 316, 17-4PH and alloy steels for shafts, fittings and wear surfaces, with passivation, heat treatment or coating as specified.

Plastics, brass and copper

POM, PA, PC, PEEK and brass or copper alloys for insulating, low-friction and conductive components.

How a CNC machining order runs

1. Drawing review

We check datums, tolerances, tool access, internal radii and finish allowances, and return open questions with the quotation.

2. Quotation

The quotation states the machining route, material, finish, inspection scope and lead time for your quantity.

3. First article

First parts are machined and measured against the drawing revision, with a dimensional report for approval.

4. Repeat batches

Programs, fixtures and the inspection plan are kept under revision control for every following order.

Typical CNC machined components

  • Robot joint housings, arm links and end-effector brackets
  • Precision shafts, bushings, sleeves and couplings
  • Motor mounts, sensor brackets and mounting plates
  • Fixture plates, locating blocks and workholding components
  • Gears, racks, worm components and timing pulleys machined to drawing
  • Manifolds, valve bodies and sealing interfaces

CNC machining FAQ

Do you machine single prototypes?

Yes. The minimum order is one piece, and the same drawing review and inspection approach is used for prototypes, pilot lots and repeat production.

Which CNC process will my part need?

Prismatic parts with pockets and hole patterns are usually milled, rotational parts are turned, and multi-face or angled features may suit 5-axis machining. The route is proposed in the quotation after reviewing the model and drawing.

What files are needed for a CNC machining quote?

A STEP model and a PDF drawing with the current revision, material grade, quantity, finish and any inspection requirements. Tolerances, threads and datums should be shown on the 2D drawing.

How is lead time decided?

Lead time depends on the complexity of the parts, the quantity, finishing and material availability. Typical production lead time is 7 to 30 days, depending on how complex the parts are and how many you need. It is counted from order confirmation and receipt of the payment due before production, as stated on the quotation, to the day the inspected parts are packed and ready to ship. Shipping transit time is not included and is confirmed separately on the quotation. If the material is not in stock and has to be bought in, allow up to about one more week. The lead time for your parts is stated on the quotation.

PROJECT INQUIRY

Send the drawing for your CNC machining quote.

Add the quantity for this order and what you expect over the next year. We reply with questions or a quotation that states the route, finish, inspection and lead time. Or email the drawing to info@tovilon.com.

Request a Quote
WhatsApp